Alltel v3m Signal strentgh

[arriagga]

hi, everybody.

i had a version v3m, but because of the problem with the
micro sd I flashed it to alltel (with a monster pack)
almost every working fine. this are my 2 problems.

1º the Signal strentgh is never 1x like it was with verizon,
only digital en very weak.

2.º I cant connect to the internet with my cellphone.

do you have any ideas you could give to help me with this problems

thanks

[nevarDeath]

check here:
http://mark.cdmaforums.com/Monster2.htm

specifically this part:
3c1. NOTE: V3M/K1M for EVDO Data, you must do the following before restoring.... (V3C users do not need to do this indented part!)

These steps are experimental and if successful, eliminate the need to do Section 7 below....

Earlier, you used RadioComm to backup, which created a file name that defaults to your phone's ESN number. Example: A123455.NVM

Before we restore that, V3M and Krzr k1m users should open the A123455.NVM file in notepad... (works best with WORD WRAP turned off... Format-> Word Wrap, make sure unchecked)

Look for the line that starts with M_01D2,466,0,122,... and change it to M_01D2,466,1,122,...
Look for the line that starts with M_01d1,465,1,122,... and change it to M_01d1,465,2,122,...

Now you may continue.

Start RadioComm.
If prompted about the Moto Driver Installation setup, click CANCEL. i.e. do NOT run the Moto Driver Installation...
Inside RadioComm, use the Main pulldown menu. Select MA -> CDMA1X -> 6500 Chipset Base
Use the Settings pull down menu. Select USB -> M-Link USB Driver.
In the Main RadioComm window, click on the P2K 1 tab. The PC should "beep", and you should see the Radio Detection change from a blue ciricle to a Green circle.
Use the Features pull down menu. Select NV/Seem.
In the TABLE box, click the OPEN button. Browse to the ESN .NVM file that was created in the backup steps (example: A123455.NVM) , select it, and click OK.
In the Action box, click the WRITE button.
When the WRITE has completed...
Close the seem window using the X in the upper right, then exit out of RadioComm.

Radiocomm leaves the phone in the correct mode for P2KSeem to connect, so perform the following seem edits...


3d. NOTE: V3M/K1M Only: Use P2KSeem for V710 to edit the 01D0 seem, selects the second M.IP Profile.

Fill in Seem: 01d0, Bytes (h): 7A, Record: 1
Click Load from phone.
Find Offset: 00
Check the box for Bit: 0 which sets the Hex value of the offset to 01
Click Save to Phone.

[arriagga]

Oops my bad, i did not make any backup (i know it sounds stupid, but i did) ill try everything i read here to fix it (ill do it on monday 'cause i dont have a computer here where i am now)
thanks for your help.

as i did not make any backup ,where can i get the files i need.
can i use the v3m system files on the web page you give me?
thanks a lot, for your help.

[nevarDeath]

Oops my bad, i did not make any backup (i know it sounds stupid, but i did) ill try everything i read here to fix it (ill do it on monday 'cause i dont have a computer here where i am now)
thanks for your help.

as i did not make any backup ,where can i get the files i need.
can i use the v3m system files on the web page you give me?
thanks a lot, for your help.

Yes you can use that. There's some here too: http://www.humpa.com/vzw
near the top of the page

[arriagga]

Finally I got the web service working :tapdance: (i got the files i needed from another v3m from verizon in my contry (dominican republic). and

mms too.:beer:
i also added some skins to my cell (to add them i had to use dir2flex program, ' cause i tried with pst+p2kcommander and it didn't work).
the only thing i haven't change is the D for 1X icon, i have to make some seem edit. and i dont know how to do it, but i'll learn.
my cell looks great now :beer-fresh:
thank for your help

[milkbone98]

The 1x icon indicates a working, attached web connection, maybe you need to find the seem for auto attach.

[arriagga]

Ok, ill checkit out

thanks